Delta-electronics Network Device VFD-S Instrukcja Użytkownika Pobierz pdf

English- 1

Preface

Thank you for choosing DELTA’s high-performance VFD-S Series. The VFD-S Series is

manufactured with high-quality components and materials and incorporates the latest microprocessor

technology available.

 Getting Started

This quick start will be helpful in the installation and parameter setting of the AC motor drives. To

guarantee safe operation of the equipment, read the following safety guidelines before

connecting power to the AC motor drives. For detail information, refer to the VFD-S User Manual

on the CD supplied with the drive.

DANGER!

1. AC input power must be disconnected before any wiring to the AC motor drive is made.

2. A charge may still remain in the DC-link capacitors with hazardous voltages, even if the power

has been turned off. To prevent personal injury, please ensure that power has turned off before

opening the AC motor drive and wait ten minutes for the capacitors to discharge to safe voltage

levels.

3. Never reassemble internal components or wiring.

4. The AC motor drive may be destroyed beyond repair if incorrect cables are connected to the

input/output terminals. Never connect the AC motor drive output terminals U/T1, V/T2, and

W/T3 directly to the AC mains circuit power supply.

5. Ground the VFD-S using the ground terminal. The grounding method must comply with the laws

of the country where the AC motor drive is to be installed. Refer to the Basic Wiring Diagram.

6. VFD-S series is used only to control variable speed of 3-phase induction motors, NOT for 1-

phase motors or other purpose.

7. VFD-S series shall NOT be used for life support equipment or any life safety situation.

WARNING!

1. DO NOT use Hi-pot test for internal components. The semi-conductor used in AC motor drive

easily damage by high-pressure.

2. There are highly sensitive MOS components on the printed circuit boards. These components

are especially sensitive to static electricity. To prevent damage to these components, do not

touch these components or the circuit boards with metal objects or your bare hands.

3. Only quality person is allowed to install, wire and maintain AC motor drive.

CAUTION!

1. Some parameters settings can cause the motor to run immediately after applying power.

2. DO NOT install the AC motor drive in a place subjected to high temperature, direct sunlight,

high humidity, excessive vibration, corrosive gases or liquids, or airborne dust or metallic

particles.

3. Only use AC motor drives within specification. Failure to comply may result in fire, explosion or

electric shock.

4. To prevent personal injury, please keep children and unqualified people away from the

equipment.

5. When the motor cable between AC motor drive and motor is too long, the layer insulation of the

motor may be damaged. Please use a frequency inverter duty motor or add an AC output

reactor to prevent damage to the motor. Refer to appendix B Reactor for details.

6. The rated voltage for AC motor drive must be ≤240V (≤480V for 460V models) and the mains

supply current capacity must be ≤5000A RMS (≤10000A RMS for the ≥40hp (30kW) models).

1 2 3 4 5 6 ... 21 22

Podsumowanie treści

Strona 1 - Preface

English- 1Preface Thank you for choosing DELTA’s high-performance VFD-S Series. The VFD-S Series is manufactured with high-quality components and mat

Strona 2 - Specifications

English- 10Summary of Parameter Settings a: The parameter can be set during operation. Group 0 User Parameters Pr. Explanation Settings Factory S

Strona 3 - Basic Wiring Diagram

English- 11Pr. Explanation Settings Factory SettingNOTEa1-13 Jog Acceleration / Deceleration Time d0.1 to d600 Sec d10.0 a1-14 Jog Frequency d1

Strona 4 - NPN (sink mode)

English- 12Pr. Explanation Settings Factory SettingNOTE2-00 Source of Master Frequency Command d5: Master Frequency operated by RS-485 serial commun

Strona 5 - PNP (source mode)

English- 13Pr. Explanation Settings Factory SettingNOTE3-06 Multi-Function Output Terminal 2 (Relay Output) d1: AC Drive Operational d2: Master Freq

Strona 6 - English- 6

English- 14Pr. Explanation Settings Factory SettingNOTE4-08 Multi-Function Input Terminal 5(M5) d18: Pause PLC Program d19: Counter Trigger Signal

Strona 7 - Multi-step speed 3

English- 15Pr. Explanation Settings Factory SettingNOTE d5: Disable PLC operation, but can set direction of 1st speed to 7th speed 5-08 PLC Forwa

Strona 8 - English- 8

English- 16Pr. Explanation Settings Factory SettingNOTE 6-09 Second Most Recent Fault Record 6-10 Third Most Recent Fault Record

Strona 9 - English- 9

English- 17Pr. Explanation Settings Factory SettingNOTE8-01 DC Braking Time during Start-Up d0.0 to d60.0 Sec d0.0 8-02 DC Braking time during

Strona 10 - English- 10

English- 18Pr. Explanation Settings Factory SettingNOTEd4: 8,E,1 (Modbus, ASCII) d5: 8,O,1 (Modbus, ASCII) d6: 8,N,2 (Modbus, RTU) d7: 8,E,1 (Modbus

Strona 11 - English- 11

English- 19Fault Name Fault Descriptions Corrective Actions Over current Abnormal increase in current. 4. Check for loose contacts between AC mot

Strona 12 - English- 12

English- 2Specifications Voltage Class 115V Class 230V Class 460V Class Model Number VFD-XXXS 002 004 007 002 004 007 015 022 004 007 015 02

Strona 13 - English- 13

English- 20Fault Name Fault Descriptions Corrective Actions Over-current during acceleration 3. Acceleration Time too short: Increase the Acceler

Strona 14 - English- 14

English- 21Fault Name Fault Descriptions Corrective Actions Communication Error 1. Check the RS485 connection between the AC motor drive and RS485

Strona 15 - English- 15

English- 22Model Name A B C D E F G H I 007S43B 85.0[3.35]148.0[5.83]126.0[4.96]74.0[2.92]132.2 [5.21] 5.8 [0.23]73.0[2.88]16.0[0.63]67.8[2.

Strona 16 - English- 16

English- 3Basic Wiring Diagram Users must connect wiring according to the following circuit diagram shown below. For VFDXXXSXXA/B/D/U 4.7k47KGroundin

Strona 17 - English- 17

English- 4For VFDXXXSXXE NPN (sink mode) B2U/T1V/T 2W/T3IM3~NOTE: Do not plug in a Modem or telephone line to the RS-485 communication po

Strona 18 - Fault Codes

English- 5For VFDXXXSXXE PNP (source mode) B2U/T1V/T 2W/T3IM3~NOTE: Do not plug in a Modem or telephone line to the RS-485 communication

Strona 19 - English- 19

English- 6Power Terminals MotorConnectionGround Braking ResistorAC Input Line Ter minal AC Input Line Terminal MotorConne ctionBraking Res

Strona 20 - English- 20

English- 7Terminal Explanations Terminal Symbol Explanation of Terminal Function R/L1, S/L2, T/L3 AC line input terminals (three phase) L/L1, N/L2

Strona 21 - Dimensions are in mm [inch]

English- 8Terminal Explanations Terminal symbols Terminal name Remarks RA-RC Multi-Function Indication Output Contact RB-RC Multi-Function Indicati

Strona 22

English- 9Operation steps of the Digital Keypad MODEMODEMODEMODEMODEMODEMODEPROGDATAPRO GDATAPROGDATAChange display modeSet frequencySet frequencySet

Komentarze do niniejszej Instrukcji

Brak uwag

Delta-electronics Network Device VFD-S Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Sprzęt komputerowy Delta-electronics Network Device VFD-S. Delta Electronics Network Device VFD-S User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Delta-electronics Network Device VFD-S