Delta Electronics DTB4896 Dokumentacja Pobierz pdf

Series Valve Temperature Controller

Instruction Sheet

Thanks you very much for choosing Delta DTV series valve temperature controller. Please read this instruction sheet before using your DTV to ensure proper

operation. Keep this instruction handy for quick reference.

 Warning

DANGER! CAUTION! ELECTRIC SHOCK! When the power is on, DO NOT touch the AC terminals in case an electric shock may occur. Make sure

the power is disconnected when you check the input power.

DTV is an OPEN-TYPE device. If it will cause serious injury to workers or damage on other equipments when used in a dangerous environment,

please make sure it is installed in an automatic safety protection device.

1. Always use recommended solder-less terminals: Fork terminal with isolation (M3 screw, Max. width 7.2mm). Please be sure to tighten them properly and

make sure the wire is connected to the correct terminal.

2. Prevent dust or metallic debris from falling into the device and cause malfunction. DO NOT modify or uninstall DTV series without being permitted. DO

NOT use empty terminals.

3. Keep away from high-voltage and high-frequency environment during installation in case of interference. Prevent using DTV in premises which contain:

(a) dust or corrosive gas; (b) high humidity and high radiation; (c) shock and vibration

4. The power has to be switched off when wiring or changing temperature sensor.

5. Make sure to use compensation wire which matches the thermocouple when extending or connecting the thermocouple wire.

6. Use wires with resistance when extending or connecting the platinum resistance sensor.

7. Keep the wire as short as possible when wiring a sensor to the temperature controller. Separate the power cable and load wire in order to prevent

interference and induced noise.

8. DTV is an open-type device. Make sure to install it in an enclosure which prevents dust and humidity in case of an electric shock.

9. Make sure the power cables and signal device are installed correctly before switching on the power; otherwise serious damage may occur.

10. DO NOT touch the terminals or repair the device when the power is on; otherwise an electric shock may occur.

11. Please wait for one minute after the power is switched off to allow the capacitor to discharge. DO NOT touch the internal wiring within this period.

12. DO use dry cloth and DONOT use acid or alkaline liquid to clean the device.

 Display, LED & Pushbuttons

PV: Present value

SV: Set value

%: Output percentage

AT: Auto-tuning indicator

A/M: Manual control indicator

OUT1/OUT2: Output indicator

ALM1/ALM2: Alarm output indicator

Manual/auto mode switch key

Selection/setup key

Switching page key

Left-shifting the digit

 Ordering information

DTV

Series name DTV: Delta V series valve temperature controller

1 2 3 4

Panel size

(W × H)

4896: 1/8 DIN W48 × H96 mm

9696: 1/4 DIN W96 × H96 mm

R: Valve, relay output SPST (250VAC, 5A)

 Specifications

Power input AC100 ~ 240V, 50/60Hz

Input power range 85% ~ 110%, rated voltage

Power consumption Less than 5VA

Display

2-line, 7-segment LED, 4bits and 2 bits of valve openness display

PV in red, SV and valve openness in green.

Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK

Platinum resistance: Pt100, JPt100

Input temperature sensor

Analog input: 0 ~ 5V, 0 ~ 10V, 0 ~ 20mA, 4 ~ 20mA, 0 ~ 50mA

Control method PID, PID programmable control, manual, On/Off

Control output type Relay output: SPST, Max. load 250V, 5A resistive load

Display scale 1 digit after the decimal point, or no decimal point

Sampling cycle Analog input: 0.15 sec; thermocouple/platinum resistance: 0.4 sec

Vibration resistance 10 ~ 55Hz 10m/s

3 axes 10 min.

Shock resistance Max. 300m/s

3 axes 6 directions, 3 times each

Ambient temperature 0°C ~ +50°C

Storage temperature -20°C ~ +65°C

Operation altitude Less than 2,000m

Ambient humidity 35% ~ 80% RH (non-condensing)

1 2 3 4 5 6 7 8

Podsumowanie treści

Strona 1 - Specifications

Series Valve Temperature Controller Instruction Sheet Thanks you very much for choosing Delta DTV series valve temperature controller. Please rea

Strona 2 - Setting up Parameters

 Setting up Parameters Switching Modes: DTV is in the operation mode when the power is switched on, displaying PV and SV. Press for more than 3 se

Strona 3 - Output Control

Regulation Mode Operation Mode Initial Setting Mode Select the PID group (n = 0~4) Press  PID group 0 ~ 3 Set up the temperature SV for PID

Strona 4 - PID Programmable Control

Input Sensor Type Register Value Display Range Thermocouple R type 5 0 ~ 1,700°C Thermocouple N type 4 -200 ~ 1,300°C Thermocouple E type 3

Strona 5 - Auto/Manual Mode Switch

The Number of Steps: The number of steps in each pattern (range: 0 ~ 7). For example, if the parameter is set as 2, it refers to pattern 7 will ex

Strona 6

Address Content Explanation 1002H Upper limit of temperature range The content shall not be bigger than the range. 1003H Lower limit of temperat

Strona 7 - Dimensions

Read Command Read Response Message Write Command Write Response Message ‘0’ ‘0’ ‘F’ ‘0’ ‘0’ ‘F’ ‘0’ ‘F’‘0’ ‘0’ Data content in 1000H/081xH ‘4’

Strona 8 -  Panel Cutout  Terminals

8 Panel Cutout  Terminals DTV4896/DTV9696 DTV4896R/DTV9696R 60.0 min.120.0 min.110.0 min.120.0 min.48*9696*9644.5+0.6 091.5+0.6 091+0.6 091+0.6

Komentarze do niniejszej Instrukcji

Brak uwag

Delta Electronics DTB4896 Dokumentacja

Przeglądaj online lub pobierz Dokumentacja dla Nie Delta Electronics DTB4896. Delta Electronics DTB4896 Specifications Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Nie Delta Electronics DTB4896